Diesel Diagnostics

Post a Response

Peugeot 206 2.0 HDi RHY 2001 - Non start #

Posted by Colin Calder on March 10, 2011, 6:30 pm

Year of Manufacture *: 2001
Engine Size and Code *: 2.0 HDi (RHY) Bosch common rail

Hello peebs.
This towed in today from local bodyshop where it has had minor cosmetic work and then been stood for a couple of months. Suspect it has had a jump start sometime after being stood.
Have crank but no heat plug feed or fuel injection signal or comms. I have triggered up fuel pump and checked heater plug circuit and checked all the other basics that I can think of including live feeds and earths and also looked through the archives.
I have all central locking and door chime and all other systems. I have pulled underbonnet fuse box and ECU to check for the usual grotty wiring etc:
Am getting a bit stuck on this one now and am thinking of launching the lifeboat but hate to give up and be beaten.
Would greatly appreciate any pointers on this.

I was fixing a roof for someone the other day, bit of felt, bit of flashing, bit of cement, sun was shining. No overheads (scuse the pun), no specialist tools, no advanced diagnostics and the person said none of the tradesmen had even bothered to turn up to do the job for her in over a YEAR and that all her friends were always wanting things 'fixed'.
So,shall I jump, or wait until I'm pushed.

Re: Peugeot 206 No start

Posted by phil kingdon <iframe src='https://members.boardhost.com/ukautotalk8/info/user=UKAT1433' width='330' height='300' border=0 style='border:none;'> on March 11, 2011, 7:24 am, in reply to "Peugeot 206 No start"
Phil Kingdon

Had a similar one the other day Colin,would crank, no comms, no start, turned out to be fuel pressure dump valve, one on top of pump held in with three tiny torks screws, cant recall if we got comms at all but got it going and has been returned home now for a couple of months.
I tend to keep any engine sensors ect, even faulty ones, with an explanatory note, I had one of these units that would run a car but cause it to cut out at 3k, I used this one to get succsessful start.
Hope this helps, Phil.

Re: Peugeot 206 No start

Posted by martin simonsohn <iframe src='https://members.boardhost.com/ukautotalk8/info/user=ukat3223' width='330' height='300' border=0 style='border:none;'> on March 11, 2011, 11:16 am, in reply to "Peugeot 206 No start"
Martin Simonsohn

you ought to take a look at the double function relay on these as they do give problems with supplying ecu with power.
also take a look at the ecu and check for water ingress.also i think there is a separate earth to the gearbox that brakes off and that is for engine management.
also the inertia fuel shut off connections can give problems.
pre heaters don't activate on these unless its below 0 degrees
ps its worth checking ALL fuses in and under fuse boxes engine bay and under the dash
hope this helps martin

Re: Peugeot 206 No start

Posted by Alan Kane <iframe src='https://members.boardhost.com/ukautotalk8/info/user=UKAT5535' width='330' height='300' border=0 style='border:none;'> on March 11, 2011, 1:29 pm, in reply to "Peugeot 206 No start"
Alan Kane - Administrator

Did you check to see why you have no communication? Lack of communication and non start are likely to be caused by the same thing. Maybe shorted CAN or K Line, depending on what way this is set up, (I didn’t check a diag).

Re: Peugeot 206 No start

Posted by Colin Calder <iframe src='https://members.boardhost.com/ukautotalk8/info/user=UKAT5444' width='330' height='300' border=0 style='border:none;'> on March 14, 2011, 10:22 am, in reply to "Re: Peugeot 206 No start"
Colin Calder

Found it! The BCM has lost all codes, that's why no comms: etc:. Am looking into what will be the next move.
Colin.

« Back to index

[ Diesel Diagnostics ]