The L.C. Smith Collectors Association

The L.C. Smith Collectors Association
[ The L.C. Smith Collectors Association ]

Removing side plates, 1906 SxS

Posted by Richard Ranney on June 7, 2021, 7:14 pm

I read a thread here on removing side plates but it wasn’t for a single screw 1906 SxS. I’ve got the single stew 3 pins plate. Would it be the same and how much difficulty would it be to re-assemble? Thank you for the help.
Richard

Re: Removing side plates, 1906 SxS

Posted by David Williamson on June 8, 2021, 6:29 am, in reply to "Removing side plates, 1906 SxS"

Richard the process is the same just remove the single screw to remove the side plate. You are stating 3 pin side plate which should be a hammer gun and so just remove the single screw.

Re: Removing side plates, 1906 SxS

Posted by Richard Ranney on June 8, 2021, 10:03 am, in reply to "Re: Removing side plates, 1906 SxS"

Thanks David, I just wanted to make sure prior to doing it. It’s now the putting back on I’m leery of😂
Richard

Re: Removing side plates, 1906 SxS

Posted by David Williamson on June 8, 2021, 2:07 pm, in reply to "Re: Removing side plates, 1906 SxS"

In putting the side plate back on, which ever side you pick first you have to push that trigger forward so that the sear goes on top of the trigger plate. If not the sear will be pushing against the trigger plate and you will not get the side plate to go on.
If you have both side plates off, you can look into the hole where the sears go through and see the trigger plate, move the trigger forward and you will see the trigger plate move downward.

Re: Removing side plates, 1906 SxS

Posted by Richard Ranney on June 8, 2021, 3:02 pm, in reply to "Re: Removing side plates, 1906 SxS"

David I will be removing both sides. I’m cleaning the stock and checking the internals for debris as well. If I run in to trouble I’ll certainly be here looking for help😂. It’s going to be a wall hanger but I want it to be functional and beautiful regardless.
Richard

Re: Removing side plates, 1906 SxS

Posted by Richard Rannet on June 8, 2021, 5:26 pm, in reply to "Re: Removing side plates, 1906 SxS"

David will this decock after removing screw? Right now the right will sometimes decock by itself and will always if I pull left trigger first. I’ve got my eye on some hammers right now to pick up for this.
Richard

Re: Removing side plates, 1906 SxS

Posted by David Williamson on June 8, 2021, 5:41 pm, in reply to "Re: Removing side plates, 1906 SxS"

Removing the screw should have nothing to do with that side firing. The only thing I can think of is that at one time someone tried putting the lock plate on and did not push the trigger forward and bent the trigger plate causing the opposite trigger to fire.
The easiest way is to put the right lock plate on and look through the hole on the left side of the stock and see if the sear from the right lock is touching the left top trigger plate.

Re: Removing side plates, 1906 SxS

Posted by Carl Erickson on June 8, 2021, 6:00 pm, in reply to "Re: Removing side plates, 1906 SxS"

A 1906 hammer gun can be a fun gun to shoot. I suggest that when you are finished that you have it inspected by a competent sxs gunsmith and shoot it.

Re: Removing side plates, 1906 SxS

Posted by Richard Ranney on June 9, 2021, 7:41 pm, in reply to "Re: Removing side plates, 1906 SxS"

Side plates removed! Is there any way to bring back that case tempered look? Thanks,
Richard

« Back to index

175

[ The L.C. Smith Collectors Association ]