Renault Traffic 2.0 M9R692 2013 - MIL on, code DF002? - Unresolved #
Posted by Mark Duhigg on February 6, 2015, 1:59 pm
Year of Manufacture *: 2013 Engine Size and Code *: 2.0 M9R692
Renault with engine light coming on. Fault code DF002 but no description,no EOBD codes. Autodata just giving EOBD codes. Can any one help and point in some sort of direction. Cheers Mark
Re: Renault Traffic 2.0 M9R692 2013 - MIL on, code DF002? #
Disconnected MAF getting codes DF005 and DF009 relating to air flow and temp sensor.
Re read codes with Snap on Solus and getting code DF002 Flow Regulation Adaptive, sill non the wiser where to look. Changed fuel filter but didn't make any difference. Mark
Re: Renault Traffic 2.0 M9R692 2013 - MIL on, code DF002? #
Strange that, do you have access to any other tools? Can you try going in under vauxhall vivaro?
I'm looking here at the Renault PDF for trafic phase 2 and 3, M9R692 engine with EDC17C11/EDC17C42, and it doesn't even have DF005 or DF009 faults listed.
Does this van run?
Re: Renault Traffic 2.0 M9R692 2013 - MIL on, code DF002? #
Using 3 scanners Snap on,Autocom and launch Snap on Vauxhall and Renault DF002=flow regulation adaptive. Autocom 002f620=undocumented code Launch=some random code that don't make any sense
Mark
Re: Renault Traffic 2.0 M9R692 2013 - MIL on, code DF002? #
DF002 PRESENT OR STORED AIR TEMPERATURE SENSOR CIRCUIT 1.DEF: Signal outside lower limit. 2.DEF: Signal outside upper limit.
Note: The inlet air temperature sensor is integrated into the air flowmeter.
Conditions for application to a stored fault: The fault is declared present after the ignition has been switched on.
If the fault is present: ¡V The turbocharging pressure is limited. ¡V The EGR valve is closed. ¡V The damper valve is open
Special notes: After this fault appears: ¡V Reduction in engine performance, ¡V The OBD and Level 1 warning lights illuminate
See Wiring Diagram Technical Note for Trafic II ph 2 and ph 3.
Check the connection and condition of the air flowmeter connector, component code 799. Check the connection and condition of the injection computer connector, component code 120. If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring. Check the insulation, continuity and the absence of interference resistance of the following connections: ¡V 3ABQ between components 799 and 120. ¡V 37X between components 799 and 1834. If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring. Measure the resistance of the air temperature sensor, component code 799 between connections 3ABQ and 37X of the air flowmeter, component code 799 If the resistance measured is not between 50 ohms and 30K ohms replace the air flowmeter, component code 799 (see MR 408, Mechanical, 12A, Fuel mixture, Air flowmeter: Removal - Refitting).
Did not get to bottom of this. Customer wanted van back He was going to try warranty route(3 years or 60,000 Miles) but had first 20k service 10,000 miles late. Cheers for help and sugestions. Mark