Posted by sgirish
on March 8, 2005, 4:51:14, in reply to "FDT problems"
210.94.41.89
Hi,
You are getting this error "unable to set baudrate" because you have not given the correct input frequency. I was also facing the same problem initially. But once i gave the correct clock frequency, it started working fine. Hope the same happens with you
--Previous Message--
: Hello all,
: I am trying to connect via serial
: port from the FDT to the 3DK. I need
: support regarding that, because the
: connection is not completed. There
: is an error at the end when the FDT
: is determining the baud rate. This
: happens for every baud rate I try to
: determine.
:
:
: See this log file form the FDT.
:
: THE LOG FILE:
: Initiating BOOT SCI sequence
: Attempting 9600
: Received immediate response from
: device: 0xE6
: Detected 0.18um device
: Requesting supported devices list...
: List received - 1 selectable
: device(s)
: Device Code, Product Code:
: 0t02,HD64F2166
:
:
: Selecting Device - 0t02
: Device selected
:
:
: Requesting supported clock modes
: list...
: List received - 1 selectable clock
: mode(s)
: Clock Mode: 0x00
:
:
: Selecting Clock mode - 0
: Clock mode selected
:
:
: Requesting supported multiplication
: ratio list...
: List received - 1 types of
: multiplication ratio(s)
: Multiplication Ratio type 1:
: Multiplication Ratio = 1
:
:
:
:
:
: Requesting supported operating
: frequencies list...
: List received - 1 operating
: frequency range(s)
: Operating Frequency Range 0:
: 5.00 - 40.00 MHz
:
:
: Requesting user-boot ROM
: information...
: List received - 1 user-boot ROM
: area(s)
: User Boot ROM Area 0: 0x00000000
: - 0x00001FFF
:
:
: Requesting user ROM information...
: List received - 1 user ROM area(s)
: User ROM Area 0: 0x00000000 -
: 0x0007FFFF
:
:
: Requesting erase block
: information...
: List received - 16 erase block(s)
: Erase Block 00: 0x00000000 -
: 0x00000FFF
: Erase Block 01: 0x00001000 -
: 0x00001FFF
: Erase Block 02: 0x00002000 -
: 0x00002FFF
: Erase Block 03: 0x00003000 -
: 0x00003FFF
: Erase Block 04: 0x00004000 -
: 0x0000BFFF
: Erase Block 05: 0x0000C000 -
: 0x0000CFFF
: Erase Block 06: 0x0000D000 -
: 0x0000DFFF
: Erase Block 07: 0x0000E000 -
: 0x0000EFFF
: Erase Block 08: 0x0000F000 -
: 0x0000FFFF
: Erase Block 09: 0x00010000 -
: 0x0001FFFF
: Erase Block 10: 0x00020000 -
: 0x0002FFFF
: Erase Block 11: 0x00030000 -
: 0x0003FFFF
: Erase Block 12: 0x00040000 -
: 0x0004FFFF
: Erase Block 13: 0x00050000 -
: 0x0005FFFF
: Erase Block 14: 0x00060000 -
: 0x0006FFFF
: Erase Block 15: 0x00070000 -
: 0x0007FFFF
:
:
: Requesting line size information...
: Line size received - 128
:
:
: Requesting write method
: information...
: List received - single mat write
:
:
: Requesting ECC write information...
: ECC write received - 0
:
:
: Changing baud rate to 1200 bps
: Error No 15005: 'COM1:' read time
: out
: Error No 16148: Unable to set baud
: rate value = 1200 -->> this
: happens for all baud rates
:
:
:
:
Message Thread:
« Back to thread