[ FYI FORD - MustangSteve's Ford Mustang Forum | Message Archive ]

If you wish to contribute to support this site, email mustangsteve66@yahoo.com REMEMBER!!! When posting a question about your Mustang or other Ford on this FORD MUSTANG FORUM, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.

Re: Got my "Arning drop "drilled today, what an experience!!......... Posted by ultrastang on 8/25/2009, 7:58 pm, in reply to "Re: Got my "Arning drop "drilled today, what an experience!!........." 69.150.10.93 Every Mustanger that's going to be drilling [or tapping holes] should have a can of this stuff. It's the best stuff in the world for making it easy to drill or tap metals: http://www.tapmagic.com/ It makes it really easy to drill or tap in, or through, stuff and your bits or taps will last longer too. And, it's made "right up the road" from me in Little Rock. Message Thread: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - 6sally6 8/22/2009, 8:16 pm Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - ultrastang 8/22/2009, 8:48 pm Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - Fred 8/22/2009, 8:49 pm Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - 6sally6 8/22/2009, 10:03 pm Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - Fred 8/23/2009, 12:50 am Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - 6sally6 8/23/2009, 11:12 am Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - Fred 8/23/2009, 2:13 pm Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - ultrastang 8/22/2009, 9:09 pm Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - zakdaddy99 8/23/2009, 9:42 am Re: Starting to rebuld my frontend, (66 coupe)got loads of questions...... - Murfman66 8/23/2009, 9:24 am I agree with Fred's idea to relocate farther back - MustangSteve 8/23/2009, 7:06 pm OK....I got the 3/16" back on the template butt......... - 6sally6 8/24/2009, 10:13 am Spinning the shaft does work - Opentracker 8/24/2009, 11:10 am Got the shaft centered in the A-arms and..... - 6sally6 8/24/2009, 5:45 pm Since you already have it drilled - MustangSteve 8/24/2009, 6:18 pm MS,,,,,you got mail!!!! - 6sally6 8/24/2009, 8:56 pm Got my "Arning drop "drilled today, what an experience!!......... - 6sally6 8/25/2009, 7:12 pm Re: Got my "Arning drop "drilled today, what an experience!!......... - ultrastang 8/25/2009, 7:16 pm Re: Got my "Arning drop "drilled today, what an experience!!......... - 6sally6 8/25/2009, 7:34 pm Re: Got my "Arning drop "drilled today, what an experience!!......... - ultrastang 8/25/2009, 7:58 pm Ultra... for some reason - jerseyjoe 8/25/2009, 8:07 pm Re: Ultra... for some reason - ultrastang 8/25/2009, 8:52 pm I found that this works very well - Ron68 8/26/2009, 12:48 am Gunna weld the - jerseyjoe 8/25/2009, 7:59 pm Don't know........should-eye?? - 6sally6 8/25/2009, 8:11 pm Not unless you want to. - CraigMBA 8/26/2009, 10:21 am Re: Spinning the shaft does work - 6sally6 8/31/2009, 11:35 pm NO it doesn't either!!! - 6sally6 9/2/2009, 9:40 pm You need the caster... - MustangSteve 9/2/2009, 9:44 pm Re: You need the caster... - 6sally6 9/2/2009, 9:50 pm If it was ez, everybody would be doing it........... - 6sally6 9/3/2009, 6:24 pm Tires and wheels that fit the car !!! - MustangSteve 9/3/2009, 7:31 pm I have the 600# springs I took off my 66... - MustangSteve 9/3/2009, 7:32 pm Go get'um Ramses....... - 6sally6 9/3/2009, 9:33 pm Did you remove some alignement shims when you did the drop??? - Daze 9/8/2009, 1:54 pm Re: Did you remove some alignement shims when you did the drop??? - hmartin025 9/8/2009, 2:08 pm

REMEMBER!!! When posting a question about your Mustang or other Ford on this FORD MUSTANG FORUM, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.